BKPTT - ALLOY C-62400 FORGINGS
- MSDS: BKPTT
- Manufacturer: BENSALEM ALLOYS LTD
- Product Name: ALLOY C-62400 FORGINGS
- National Stock Number: 3439-00N015112
Product Identification
Product ID:ALLOY C-62400 FORGINGS
MSDS Date:01/01/1987
FSC:3439
NIIN:00N015112
MSDS Number: BKPTT
Responsible Party
BENSALEM, PA 19020
US
Emergency Phone: 215-639-2200
Info Phone: 215-639-2200
Cage: 0MCP1
Contractor
Telephone: 215-639-2200
Cage: 0MCP1
Ingredients
ALUMINUM (SARA III)
CAS: 7429-90-5
RTECS: BD0330000
Fraction By Weight: 10.5%
OSHA PEL 15MG/M3 DUST/5 FUME
ACGIH TLV: 10MG/M3 DUST; 9192
COPPER (SARA III)
CAS: 7440-50-8
RTECS: GL5325000
Fraction By Weight: 86.0%
OSHA PEL 0.1MG/M3 FUME/1 DUST
ACGIH TLV: 0.2MG/M3 FUME; 9192
EPA Report Quantity: 5000 LBS
DOT Report Quantity: 5000 LBS
IRON OXIDE
CAS: 1309-37-1
RTECS: NO7400000
Fraction By Weight: 3.5%
OSHA PEL 10 MG/M3 (FE)
ACGIH TLV: 5 MG/M3(FE),B2; 9293
MAY REQ SPECIAL EYE PROT INCLUDING FACESHIELDS &
RTECS: 9999999ZZ
Hazards
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ALUMINUM: AL DUST/FINES & FUMES ARE A
LOW HLTH RISK BY INHAL & ARE NORMALLY TREATED AS NUISANCE DUST IN
NORM OPS (MILL/CUT/GRIND). THE AIHA HYGIENE GUIDE LIST TOX BY
INGEST AS "NONE EXPECTED." COPPER: MELT/GRIND/CUT MAY PRDCE
FUMES/DUST EXPOS & BRTHG FUMES/DUST MAY PRESENT POTENTIALLY
SIGNIFICANT (SEE EFTS OF OVEREXP)
Explanation of Carcinogenicity:NONE
Effects of Overexposure:HLTH HAZ: HLTH HAZ. FUMES MAY CAUSE METAL FUME
FEVER W/FLU-LIKE SYMPS & SKIN/HAIR DISCOLOR. WHILE INDUS DERM HAS
NOT BEEN RPTD, KERATINIZATION OF HANDS/SOLES OF FEET HAS BEEN RPTD.
SYSTEMICALLY AS WEL L, CU DUST/FUME CAUSE IRRIT OF THE UPPER RESP
TRACT, METALLIC TASTE IN MOUTH, NAUS. IRON: INHAL OF FUMES/(SEE
SUPP DATA)
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.
First Aid
First Aid:EYE: FLUSH WELL WITH RUNNING WATER FOR AT LEAST 15 MINUTES TO
REMOVE PARTICULATE. GET MEDICAL ATTENTION. SKIN: VACUUM OFF EXCESS
DUST. WASH WELL WITH SOAP AND WATER. AVOID BLOWING PARTICULATE INTO
THE ATMOSPHERE. INHAL: REMOVE TO FRESH AIR. GET MEDICAL ATTENTION.
INGEST: SEEK MEDICAL ATTENTION IF LARGE QUANTITIES OF MATERIAL HAVE
BEEN INGESTED.
Fire Fighting
Extinguishing Media:USE SPECIAL MIXTURES OF DRY CHEMICAL OR SAND.
Fire Fighting Procedures:FIREFIGHTERS SHOULD WEAR NIOSH/MSHA APPROVED
SCBA AND FULL PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:SOLID, MASSIVE FORM NOT COMBUST. DUST
FORM CREATES MODERATE FIRE HAZARD WHEN EXPOSED TO HEAT, FLAMES,
CHEM RXN, OR CNTCT W/POWERFUL OXIDIZERS.
Accidental Release
Spill Release Procedures:NO SPECIAL PRECAUTIONS ARE NECESSARY FOR
SPILLS OF BULK MATL. IF LARGE QTYS OF DUST ARE SPILLED, REMOVE BY
VACUUMING OR WET SWEEPING TO PVNT HEAVY CONC OF AIRBORNE DUST.
FOLLOW FEDERAL, STATE & LOCAL REGS CONCERNING THE DISPOSAL OF
WASTE.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:STORE MATERIAL AWAY FROM INCOMPATIBLE
MATERIALS AND KEEP DUST FROM SOURCES OF IGNITION.
Other Precautions:USE PRECAUTIONS IN LIFTING AND PREVENT DROPPING.
Exposure Controls
Respiratory Protection:IF EXPOSURE ABOVE THE PEL OR TLV, USE A
NIOSH/MSHA APPROVED RESPIRATOR FOR FUME OR DUST, DEPENDENT UPON THE
SOURCE OF AIRBORNE CONTAMINANT.
Ventilation:REQUIRED IF DUST OR FUME CREATED IN HANDLING OR WORKING ON
THIS MATERIAL.
Protective Gloves:AS APPROP FOR MELT, GRIND, CUT, WELD OPS
Eye Protection:SEE SUPP DATA.
Other Protective Equipment:AS REQUIRED FOR THE WORK DONE ON OR WITH THE
METAL.
Work Hygienic Practices:AS REQUIRED FOR THE WORK DONE WITH THESE
FORGINGS. ALWAYS EVAL JOBS DONE I/A/W OSHA/RELEVANT STATE, FED, OR
LOCAL STDS.
Supplemental Safety and Health
EFTS OF OVEREXP: DUST MAY CAUSE AN APPARENT BENIGN PNEUMOCONIOSIS
(SIDEROSIS). THIS DISEASE IS RPTD NOT TO BE DISABLING, BUT MAKES
X-RAY DIAGNOSIS OF OTHER LUNG CNDTNS DFCLT/IMPOSS. EYE PROT: REQD
FOR MELTING, GRINDING, CUTTING, WELDING OPS. MIN REQUIREMENT OF
CHEM WORK GOGGLES . MELTING/WELDING (SEE INGRED 04)
Chemical Properties
HCC:N1
Melt/Freeze Pt:M.P/F.P Text:1550F,843C
Spec Gravity:7.5-9.0
Solubility in Water:INSOLUBLE
Appearance and Odor:YELLOW SOLID WITH NO ODOR.
Stability
Stability Indicator/Materials to Avoid:YES
ACIDS, BASES, AND OXIDIZERS.
Stability Condition to Avoid:STABLE UNDER NORMAL CONDITIONS OF
TRANSPORT AND STORAGE. MOLTEN METAL MAY REACT VIOLENTLY WITH WATER.
Hazardous Decomposition Products:METAL FUME OR DUST.
Disposal
Waste Disposal Methods:DISPOSE OF IN ACCORDANCE WITH FEDERAL, STATE AND
LOCAL REGULATIONS. CLEANUP PERSONNEL SHOULD WEAR NIOSH/MSHA
APPROVED RESPIRATORS AND PROTECTIVE CLOTHING.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.